Intelligent Manufacturing and Energy Sustainability

Performance Evaluation of Multi-Layer Barriers for Machine-Induced Low Frequency Noise Attenuation.-&nbsp;Planing Process on AISI S-1006, S-7 and S-4340, based on Johnson-Cook Model Using Numerical Technique.-&nbsp;An Analytical Study of Diametral Error in Simultaneous Turning Process.-&nbsp;Improvement of Electric Heater Design for Household Cooking Application in Developing Countries.-&nbsp;Embodiment of an Efficient Brown's Gas Compound Fuel Tank.-&nbsp;Automated Solar Photovoltaic Panel Cleaning/Cooling System using Air-water Mixture and Sustainable Solutions to Off-grid Electrification.-&nbsp;Design and fabrication of four way multi hacksaw cutting machine.-&nbsp;Adhesion strength of Plasma Sprayed Coatings-A Review.-&nbsp;An Experimental Studies on the Polymer Hybrid Composites- Effect of fibers on Characterization.-&nbsp;Design Analysis and Pressure Loss Optimization of Automobile Muffler.-&nbsp;Different Module for car parking system demonstrated using Hough Transform for smartcity development.-&nbsp;Effect of Arrangement and Number of Water Mist Spray Nozzles on Air Humidity.-&nbsp;Vibration Condition Monitoring of Spur Gear Using Feature Extraction of EMD and Hilbert Huang Transform.-&nbsp;Comparative Study of PWM Technique for Switching Loss Reduction and Acoustic Noise Reduction in VSI fed Drives.-&nbsp;An Improved Genetic Algorithm for Production Planning and Scheduling Optimization Problem.-&nbsp;Automatic Calibration for Residential Water Meters by Using Artificial Vision.-&nbsp;"Hardware in The Loop" of a flow plant embedded in FPGA, for process control.-&nbsp;Error Diagnosis in Space Navigation Integration using Wavelet Multi Resolution Analysis with General Regression Neural Network.-&nbsp;Hydromagnetic squeeze film performance of two conducting longitudinally rough elliptical plates.-&nbsp;Performance and Emission Characteristics of Biodiesel from Rapeseed & Soybean in CI Engine.-&nbsp;A Practical approach to Camera Calibration for Part Alignmentfor Hybrid Additive Manufacturing using Computer Vision.-&nbsp;Development of a colour and orientation detection system for small part feeding.-&nbsp;Comparative analysis on battery used in Solar Refrigerated E-rickshaw in India.-&nbsp;“Application of Value Stream Mapping (VSM) in a Sewing Line for Improving Overall Equipment Effectiveness (OEE): A Case Study”.-&nbsp;CFD analysis to increase heat transfer in pipe with combined effect of circular perforated ring and twisted tape insert.-&nbsp;Study On Solar Parabolic Trough Collector With Different Copper Absorber Tubes.-&nbsp;Harmonic Analysis for Bidirectional Grid Connected Converter for Electrical Vehicle during Charging and Discharging Operations.-&nbsp;Effect of tribolayer on the sliding wear behavior of detonation sprayed Alumina-Titania coatings.-&nbsp;Development of Sustainable Cementitious Binder Utilizing Silicomanganese Fumes.-&nbsp;Review on Sliding wear of Ti6Al4V alloy concerning counterface and sliding conditions.-&nbsp;Hardness and Microstructure studies on the effect of Solution treated-age hardened Al-6082 Alloy.-&nbsp;Floating Photo Voltaic Thin Film Technology - A Review.-&nbsp;Effect of Ethanol fumigation on performance and combustion characteristics of Compression Ignition Engine fuelled with Used Cooking Oil Methyl Ester in dual fuel mode.-&nbsp;Estimation and Moderation of Harmonics in Distribution Systems.-&nbsp;Theoretical Evaluation of Energy Performance of a Vapour Compression Refrigeration System Using Sustainable Refrigerants.-&nbsp;Effect of Autofrettage on the properties of the Aluminum Cylinders.-&nbsp;Influence of Graphene and Tungsten Carbide Reinforcement on Tensile and Flexural strength of Glass Fiber Epoxy Composites.-&nbsp;Investigation of partial discharge due to copper spherical particle in power transformer under various oil flow models using CFD.-&nbsp;A high power high frequency isolated DC-power supply for electrical vehicle charging application.-&nbsp;Effect of Slicingthickness and Increment on the design of patient specific implant for Total Knee Replacement (TKR) using Magnetic Resonance Imaging (MRI) - A case study.-&nbsp;Microstructure and Hardness Behavior Sudy of Carbon Nanotube in Aluminium Nanocomposites.-&nbsp;Comparison of Electric field with and without corona ring for 66kV line insulator.-&nbsp;Experimental and FEA Simulation of Thermal-Fluid Interaction Between TIN Coated Tungsten Carbide Tool and Inconel-825 Workpiece.-&nbsp;The Effect of Recrystallization on Electrical Resistivity of Stir Casted SiCP/AA6061 Composite after Shot Peening.-&nbsp;Static Stress Analysis of WYE-Piece for penstock application.-&nbsp;Comparative Investigation on Gas Tungsten Arc Welding and Friction Stir Welding of Electrolytic Tough Pitch Copper Plates.-&nbsp;Synthesis and Characterisation of Functionally Graded Ceramic Material for Aerospace Applications.-&nbsp;CI Engine Characteristic Investigation by Application of Metal Based Additives with Biodiesel Blends.-&nbsp;Simulation of underground cable faults (defects) with the detection of partial discharge.-&nbsp;Comparison of CI Engine performance parameters and Emissions by varying designs of Intake Manifolds.-&nbsp;Variation of Time Lag, Decrement Factor and Inside Surface Temperature with Solar Optical Properties of Building Envelope in Different Climatic Zones of India.-&nbsp;Study On Tensile and Hardness Properties of Al7075 Alloy Reinforced With Graphite, Mica and E-Glass.-&nbsp;ANN based fault classification and section identification technique using superimposed currents for three-terminal transmission line.-&nbsp;An analytical investigation for combined pressure driven and electroosmotic flow without the Debye–Huckel approximation.-&nbsp;Addressing the Green tribology advancement, future development and challenges.-&nbsp;Effect of Drying Temperature to the Drying Characteristic, Morphology and Peak Viscosity of Traditionally Processed Sago Starch (Lemantak).-&nbsp;Evaluating Mechanical Properties of Egg Shell and Coco Peat Reinforced Epoxy Composite.-&nbsp;Design Modification of Rear Axle Housing by Fatigue Failure Analysis.-&nbsp;Mixture Design using Low Cost Adsorbent Materials for Decolourisation of Biomethanated Distillery Spent Wash in Continuous Packed Bed Column.-&nbsp;Prediction of the WPPO Biodiesel Fuelled HCCI Engine Using Artificial Neural Networks.-&nbsp;Dimensional Analysis of Form Drilling parameters by Buckingham pi theorem and optimization of heat generation in Form drilling process by Taguchi.-&nbsp;Comparison of ductile, flexural, impact and hardness attributes of sisal fiber reinforced polyester composites.-&nbsp;Optimization of EDM Process Parameters using Standard Deviation and Multi-Objective Optimization on the basis of Simple Ratio Analysis (MOOSRA).-&nbsp;Modeling and Simulation of Trans Z-source Inverter with Maximum Constant Boost PWM Control for Solar PV System.-&nbsp;Driver Drowsiness Monitoring System.-&nbsp;Detection and Controlof Water Leakage in Pipelines and Taps Using Arduino Nano Microcontroller.-&nbsp;Smart Automated Processes for Bottle-filling Industry using PLC-SCADA System.-&nbsp;Effect of Stirring Speed During Casting on Mechanical Properties of Al-Si Based MMCs.-&nbsp;Exploration of Pillars of Industry 4.0 using Latent Semantic Analysis Technique.-&nbsp;An Overview of Different Topologies of DC-DC Bidirectional Converter for Different Applications.-&nbsp;An Approach to detect and classify defects in Cantilever Beams using Dynamic Mode Decomposition and Machine Learning.-&nbsp;Musculoskeletal Simulation and Analysis of Upper Limb Rehabilitation Device.-&nbsp;Fuzzy Regenerative Braking Strategy.-&nbsp;A New Framework for Secure utsourcing&nbsp;<div>of Medical Data.-&nbsp;A Comprehensive View for Providing the Decision on Medicare data.-&nbsp;Predicting Cardiac-Arrhythmia&nbsp;Using QRS Detection and Multi-Layer Perceptron.-&nbsp;Full Length Driver Drowsiness Detection Model – Utilising Driver Specific Judging Parameters.-&nbsp;Enterprise Reporting Solution on Integrating Business Intelligence for&nbsp; Operational and Financial Data.-&nbsp;&nbsp;Accelerating The Classifier Training Using Various Boosting Schemes Within Cascades Of Boosted Ensembles (Cobes).-&nbsp;Service Layer Security Architecture For Iot Using Biometric Authentication And Cryptography Technique.</div>